A paper glued with masking tape to a rigid support (wood, thick cardboard) is a suggestion. It is also advisable to use a “witness” surface on which to apply the layers of lacquer at the same time as on the piece to be finished. To become familiar with the process, it is advisable to test on discarded wood, in order to evaluate for yourself the characteristics of the process of finishing a guitar with “Nitorlack” lacquer guitars. The drip can also be “cut” with a razor blade, a faster method and one that avoids the accidents that can be caused by excessive sanding. If you accidentally get a “drop” or “drip” during application, allow the finish to dry for 24 hours and level by sanding with P400 sandpaper, preferably on a hard sanding block. As more experience is acquired with the product and the finishing method, fewer coats will be necessary and finer finishes can be achieved. ![]() If you have not finished an instrument before, it is advisable to apply 9 to 12 coats, so you will be sure not to sand or polish the finish too much, leaving parts with “bare” wood. This will give a thickness of approximately 150 microns (0.15 mm) depending on how much sanding is done, how much lacquer is applied in each coat and what thickness of finish is desired. Tips and General RecommendationsĪ finish with “Nitorlack” lacquer for guitars, depending on factors such as whether the wood is stained or not, and how many coats of color are given, should have a total of 6 to 10 coats in total, counting background – color – finish, with a minimum of 3-4 coats of gloss finish. Perform a first polishing process with the white sponge and finish with the black sponge until a mirror shine is achieved.Ĭlean with a cloth the remains of polish and the guitar will be finished. Check the heating regularly during polishing. It is recommended to polish at 1500 to 2000 rpm without pressure to avoid overheating the finish. It is advisable to apply a few drops of soap to the water to facilitate the sanding.Īpply a few drops of polish on the surface of the guitar and on the polishing sponge. Try to sand in straight line without exerting too much pressure to avoid making deep marks that will be difficult to remove with the polish. Sand to the water with a gradual process with sandpaper 1200-1500-2000 until all the imperfections of the application disappear. Once we see that the finish is completely uniform and the guitar is finished to our liking it is important NOT TO SAND the last coat that we have applied and let it dry for 2 to 3 weeks to polish and get the maximum brightness. It is recommended to apply a minimum of 3 coats. We apply coats of finish sanding between them with P800 leaving to dry 24 hours between coats. The application process of the finish is the same as the base coat. It is recommended to apply a minimum of 2 coats, until the entire background is covered and we see that the color is completely uniform.īe especially careful when sanding the first coats of color to avoid peeling. We apply layers of BLACK GLOSS color sanding between them with P800 leaving to dry 24 hours between coats. Color Black Gloss (or other Nitorlack Color) We will apply the product until we see that there are no imperfections, it is perfectly level and the pore of the wood is completely closed. ![]() We will sand with P800 grain between coats. The base coat is the layer of varnish that will build the base of the finish, providing a uniform surface. Application of the White Primer – Nitorlack Primer White ![]() The objective of this first step is to obtain a perfectly smooth surface without defects or roughness to proceed with the application of the first coats of primer. Once the pore is filled, or in case of woods with little pore, we sand with P400 grain to obtain a uniform surface, always in the direction of the grain. The woods with a lot of pore like ash or mahogany, whenever a closed pore finish is desired, a grain filler must be applied to fill the pore, this product can be found in our store. The wood must be free of imperfections and stains. Here are the necessary steps and tips to follow to paint a guitar in Black Gloss but you can do it in any other color: 1. You can choose any of the popular Fender or Gibson colors and look for a lot of guides and tutorials about how to paint your guitar easy. The easiest way is buy aerosol cans of paint in Nitorlack Guitar Coatings. With this tutorial we will going to try to do it simple and hopefully you will be able to paint your guitar body without wanting to kill me. There are many ways to paint a guitar body, some are simple, some are multi-staged and hard to follow.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |